OSMOCEM FLEX MONO

Cementitious, flexible, single-component waterproofing product

Cod: OSM.0283

Componente: 1

Aspect: Praf

Osmotic cementitious waterproofing from a single-component, fibre-reinforced modified polymer, being super adhesive and deformable, with a plastic-elastic conduct. Ideal for waterproofing beneath tiles and for protecting concrete. It is easily applied by trowel, brush or roller, both on horizontal and vertical surfaces. Offers a 30% higher yield than two-component systems.

Linee di appartenenza

Caracteristici generale

conservare

Conservare: 12 luni

diametrul-maxim-al-agregatului

Diametrul maxim al agregatului: < 0.4 mm

pot-life

Pot life: 40 min

temperatura-de-utilizare

Temperatura de utilizare: +5 / +35 °C

Specificații tehnice

> 0.75 mm

Absorbție capilară

0.06 kg•h^0.5/m²

Densitate

1700 kg/m³

Forţa de aderenţă

1.00 N/mm²

Întinderea la rupere longitudinală

17.2 %

Modul elastic static

3500 N/mm²

Permeabilitate la vaporii de apă

240 μ

Rezistenţa la comprimare la 07 de zile

> 1 N/mm²

Rezistenţa la comprimare la 28 de zile

> 1.5 N/mm²

Rezistenţa la flexiune la 07 de zile

> 1.2 N/mm²

Rezistenţa la flexiune la 28 de zile

> 2.5 N/mm²

Culori disponibile

- Gri

Ambalaje şi dimensiuni

- Sac 25 kg

- Paletă: 50 x (Sac 25 kg)

Caracteristici

One-component product, modified polymer, flexible and deformable, which requires only the addition of water. The application is easy and versatile, thanks to the variable consistency obtained by adjusting the amount of water added (within the allowed range and indicated in the "Instructions for use" paragraph), without dripping in vertical applications. 30% higher yield than two-component systems.

Consumuri

Approximately 1.4 kg / m² of OSMOCEM FLEX MONO for each millimeter of thickness to be created.

Domenii de utilizare

Waterproofing of balconies, terraces, bathrooms, showers, swimming pools, before laying ceramic coverings. Waterproofing of concrete structures, plasters and cementitious screeds, as long as they are sufficiently porous and absorbent and without waterproofing and / or water-repellent surface treatments, both chemical (siloxane, epoxy, polyurethane, etc.) and natural (waxing).

Pregǎtirea suporturilor

The application surfaces must be clean, free of dirt, crumbly and incoherent parts, dust, water-repellent treatments in general, etc. Any cracks due to plastic or hygrometric shrinkage, if present, must be preliminarily reclaimed with suitable products and techniques. In micro-cracked or particularly stressed areas, it is important to insert ARMAGLASS 160, an alkali-resistant fiberglass mesh, in the first fresh layer of OSMOCEM FLEX MONO. Immediately after laying the mesh, OSMOCEM FLEX MONO must be finished with a flat trowel (see also "Instructions for use").
In the case of large cladding surfaces, it is necessary to provide "chimneys" for venting the steam, suitably located.

Mod de utilizare

OSMOCEM FLEX MONO must be mixed with clean water. The following water additions are allowed:
• 22-24% for application with a trowel.
• Maximum 30% for brush-roller application.

It is recommended to mix with a low speed mixer for at least a couple of minutes and, in any case, until a perfectly homogeneous and lump-free mixture is obtained. The addition of other ingredients (binders, aggregates, additives) must be absolutely avoided. A light wetting of the support is allowed immediately before the product is spread. Dry substrates must be previously primed with BOND PLUS (mixed with water in a ratio of 1: 1).
The typical application involves an application of about 3 mm of OSMOCEM FLEX MONO in two layers. The maximum recommended thickness for each applied layer is: by trowel / spray: 2 mm, by roller / brush: 1 mm.

When waterproofing terraces and balconies, OSMOCEM FLEX MONO must be applied in two successive coats, with a thickness of approximately 1.5 mm each (approximately 2.2 kg / m² per coat), each of which must be applied when the previous one appears stable. (not earlier than 4 hours at 20 ° C). It is recommended to interpose the ARMAGLASS 160 alkaline-resistant glass fiber mesh in the thickness of OSMOCEM FLEX MONO between the first and second coat. The PROBAND butyl self-adhesive strip must also be prepared between the screed and the elevation walls. Finally, it is recommended to position the special elastic band ELASTOTEX 120, or ELASTOTEX 120 CLOTH, in correspondence with any expansion joints, fixing it with the same OSMOCEM FLEX MONO. Do not use OSMOCEM FLEX MONO on heavily degraded or inconsistent substrates, as they would risk nullifying the goodness of the waterproofing. Do not apply on slightly or non-porous substrates or substrates previously coated with water-repellent treatments in general, unless after appropriate roughening using bush hammering machines, sanders and equipment suitable for preparatory treatments of the substrates, or after appropriate treatment with suitable polymeric primers.

Metode de aplicare

- Panou

- Rulou

- Spatulă

Curǎțarea instrumentelor

- Apă

Suporturi permise

- Tencuieli

- Beton

- Mortare cimentoase din var si mixte

- Prefabricaţi

- Ţigle şi plăci (gresie, faianţă)

- Şape de substrat

- Cărămizi

- Polistiren

Contactați-ne imediat

Vuoi saperne di più sui nostri prodotti?

Atenție, introduceți datele în mod corect
Atenție! Introduceți adresa de email corectǎ
Atenție, introduceți datele în mod corect

Prin trimiterea, accept acceptarea declarației de confidențialitate

Atenție, introduceți datele în mod corect

Abonare la buletine informative

Trimteți mai departe

Produse în evidențǎ

  • Syntech H.A.G.
  • Syntech Poliurea
  • Pro Seal