Cod: SYN.0303
Componente: 2
Aspect: Lichid
SYNTECH POLIUREA SPRAY-SOFT is a solid VOC Free polyurea that can only be applied by spray using suitable bimixer machines. Designed ad hoc for waterproofing of all types. SYNTECH POLIUREA SPRAY-SOFT is made up of amines and polyols and is of the aromatic type. It is characterized by a high degree of elongation and low modulus. It is a coating elastomer obtained from the reaction of an aromatic type isocyanate with an amine. Both materials are extremely fluid and have low viscosity and have the property of reacting very quickly. Specific for applications on bituminous membranes thanks to its low stiffness.
Utilizaţi produsul cu mănuşi de protecţie
Conservare: 6 luni
Raport de amestec: 1:1 (in volume) _
Utilizaţi produsul cu ochelari de protecţie
Greutate specifică: 1.11-1.12 (A) - 1.00-1.05 (B) g/cm³
Temperatura de utilizare: +10/ +80 °C
Consumuri: 2.2 kg/m²
Aderența la beton (test de tăiere)
> 1.5 MPa
Vâscozitate
600 +/- 200 (A) - 400 +/- 200 (B) mPas
Duritatea
85 +/-5 _
Timp de gelificare
10 s
Temperatura de acţiune
-10/ +80 °C
Permeabilitate la vaporii de apă
0.025 _
Întinderea la rupere longitudinală
400 (+/- 30) %
Întărire la atingere
> 30 s
- Window grey
- Butoiaş 200 kg [B]
- Butoiaş 225 kg [A]
Tensile strength: > 1.5 N/mm²
Colour: RAL 7040 (window grey)
From 2 to 2.5 kg of SYNTECH POLIUREA SPRAY-SOFT for each square meter of surface to be covered.
SYNTECH POLIUREA SPRAY-SOFT is particularly used as waterproofing in general; directly on deteriorated and non-damaged bituminous sheaths, concrete or as a protective coating for water containment tanks even with leaks, primary containment, flooring, purification plants, EPS coating, coating and protection of metal sheets, roofs, balconies and wooden sheds and tanks .
All surfaces must be free of contaminants, with humidity lower than 3%; the substrate temperature must be at least 3°C above the dew point. The support must offer a mechanical grip on a solid and non-yielding substrate. For this reason, where necessary, a preparation carried out with shot peening, bush-hammering, smoothing or hydro-washing is recommended. If necessary, consult Azichem's technical staff for a correct evaluation. It is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting Azichem technical staff for clarification on the most suitable type to use.
Pure polyurea SYNTECH POLIUREA SPRAY-SOFT requires a bimixer system capable of producing pressure over 180 bar and temperatures above 65° C. Contact the staff for clarification on the best gun to use and on the details relating to the air system . It is recommended to use primers from the SYNTECH POLIUREA PRIMER range and contact the Azichem technical staff for clarification on the most suitable type to use.
- Pompă bi-mixer pentru vaporizare la cald
- Diluant pentru răşini
- Beton
- Fibrociment
- Gips
- Gips carton
- Lemn
- Membrane bituminoase
- Mortare cimentoase din var si mixte
- Pereţi stâncoşi
- Prefabricaţi
- Şape de substrat
- Suprafeţe metalice
- Tencuieli
- Ţigle şi plăci (gresie, faianţă)
Vuoi saperne di più sui nostri prodotti?