SYNTECH PRIMER EP-S

Epoxy primer impregnating and consolidating, in solvent

Cod: SYN.0039

Componente: 2

Aspect: Lichid

SYNTECH PRIMER EP-S is a two-component solvent-based epoxy resin, specifically formulated for the impregnation and consolidation of medium-porous substrates, including wet ones. It is applied on cement conglomerates, stone materials, wood, etc. preliminary to epoxy, polyurethane and methacrylic cycles.

Cod vamal

3907 3000

Linee di appartenenza

Caracteristici generale

Pot life: 90 min

Greutate specifică: 0.9 ± 0.05 kg/l

Utilizaţi produsul cu mănuşi de protecţie

Produs pe bază de solvenţi

Utilizaţi produsul cu ochelari de protecţie

Temperatura de utilizare: +5 / +30 °C

Conservare: 12 luni

Specificații tehnice

Absorbție capilară

< 0.1

Întărire completă

24 h

Aderenta prin tractiune directa

PASS _

Permeabilitate la vaporii de apă

> 50 m

Reziduu sec

40 %

Determinarea densității

0.90 ± 0.05 kg/l

Vâscozitate

~ 25 mPas

Permeabilitate la CO2

> 50 m

Culori disponibile

- Chihlimbar

Ambalaje şi dimensiuni

- Cutie din metal/aluminiu 1 kg [A]

- Cutie din metal/aluminiu 1 kg [B]

- Găleată 10 kg [A]

- Găleată 10 kg [B]

- Kit: 1 Cutie din metal/aluminiu 1 kg [A] + 1 Cutie din metal/aluminiu 1 kg [B]

- Kit: 1 Găleată 10 kg [A] + 1 Găleată 10 kg [B]

Consumuri

Approximately 350 ÷ 400 g / m2 of SYNTECH PRIMER EP-S per coat, depending on the porosity and irregularities of the substrate

Domenii de utilizare

SYNTECH PRIMER EP-S is used as an adhesion promoter on porous substrates in concrete, stones, etc. for: epoxy, polyurethane and methacrylic paint cycles; epoxy, polyurethane and methacrylic flooring; surface consolidation of porous supports; consolidation and waterproofing of external flooring; dustproof treatment.

Pregǎtirea suporturilor

The support on which the epoxy, polyurethane or methacrylic system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric expansion, vibrations etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 4%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line or grouted with SYNTECH AS 21. In the event of the presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply the SYNTECH PAVIDAMP epoxy resin for "wet bottoms" beforehand. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion.

Mod de utilizare

Mix the components each in their own container before mixing. Pour component B into component A and mix for 3 ÷ 5 minutes with a drill and disperser at low speed. Avoid taking partial quantities from the packaging to avoid any errors in the ratio that would cause incorrect hardening.
SYNTECH PRIMER EP-S can be applied by brush or roller. On particularly absorbent surfaces, apply SYNTECH PRIMER EP-S in 2 coats.